Sht75 Sensörünü Kullanan varmı?( CCS C)

#include <16F877.h>
#device adc=8
 
#FUSES NOWDT                    //No Watch Dog Timer
#FUSES XT                       //Crystal osc <= 4mhz for PCM/PCH , 3mhz to 10 mhz for PCD
#FUSES NOPUT                    //No Power Up Timer
#FUSES PROTECT                  //Code protected from reads
#FUSES NOBROWNOUT               //No brownout reset
#FUSES NOLVP                    //No low voltage prgming, B3(PIC16) or B5(PIC18) used for I/O
#FUSES NOCPD                    //No EE protection
#FUSES NOWRT                    //Program memory not write protected
#FUSES NODEBUG                  //No Debug mode for ICD
 
#use delay(clock=4000000)
#use rs232(baud=9600,parity=N,xmit=PIN_C6,rcv=PIN_C7,bits=8)
 
#include <lcd.c>
 
#define sht_data_pin   PIN_b1//(Data pin veya input)
#define sht_clk_pin    PIN_b0
 
//***** SHT75 Başlatma *****
 
void comstart (void)
{
 output_float(sht_data_pin);  //data high
 output_bit(sht_clk_pin, 0);  //clk low
 delay_us(1);
 output_bit(sht_clk_pin, 1);  //clk high
 delay_us(1);
 output_bit(sht_data_pin, 0); //data low
 delay_us(1);
 output_bit(sht_clk_pin, 0);  //clk low
 delay_us(2);
 output_bit(sht_clk_pin, 1);  //clk high
 delay_us(1);
 output_float(sht_data_pin);  //data high
 delay_us(1);
 output_bit(sht_clk_pin, 0);  //clk low
}
 
//***** SHT75 yazma fonksiyonu*****
 
int1 comwrite (int8 iobyte)
{
 int8 i, mask = 0x80;
 int1 ack;
 
 //Komut gönderilir
 delay_us(4);
 for(i=0; i<8; i++)
  {
   output_bit(sht_clk_pin, 0);                          //clk low
   if((iobyte & mask) > 0) output_float(sht_data_pin);  //data high if MSB high
   else output_bit(sht_data_pin, 0);                    //data low if MSB low
   delay_us(1);
   output_bit(sht_clk_pin, 1);                          //clk high
   delay_us(1);
   mask = mask >> 1;                                    //shift to next bit
  }
 
 //Shift in ack
 output_bit(sht_clk_pin, 0);  //clk low
 delay_us(1);
 ack = input(sht_data_pin);   //get ack bit
 output_bit(sht_clk_pin, 1);  //clk high
 delay_us(1);
 output_bit(sht_clk_pin, 0);  //clk low
 return(ack);
}
 
//***** Function to read data from SHT75 *****
 
int16 comread (void)
{
 int8 i;
 int16 iobyte = 0;
 const int16 mask0 = 0x0000;
 const int16 mask1 = 0x0001;
 
 //shift in MSB data
 for(i=0; i<8; i++)
  {
   iobyte = iobyte << 1;
   output_bit(sht_clk_pin, 1);                //clk high
   delay_us(1);
   if (input(sht_data_pin)) iobyte |= mask1;  //shift in data bit
   else iobyte |= mask0;
   output_bit(sht_clk_pin, 0);                //clk low
   delay_us(1);
  }
 
 //send ack 0 bit
 output_bit(sht_data_pin, 0); //data low
 delay_us(1);
 output_bit(sht_clk_pin, 1);  //clk high
 delay_us(2);
 output_bit(sht_clk_pin, 0);  //clk low
 delay_us(1);
 output_float(sht_data_pin);  //data high
 
 //shift in LSB data
 for(i=0; i<8; i++)
  {
   iobyte = iobyte << 1;
   output_bit(sht_clk_pin, 1);                //clk high
   delay_us(1);
   if (input(sht_data_pin)) iobyte |= mask1;  //shift in data bit
   else iobyte |= mask0;
   output_bit(sht_clk_pin, 0);                //clk low
   delay_us(1);
  }
 
 //send ack 1 bit
 output_float(sht_data_pin);  //data high
 delay_us(1);
 output_bit(sht_clk_pin, 1);  //clk high
 delay_us(2);
 output_bit(sht_clk_pin, 0);  //clk low
 
 return(iobyte);
}
 
//***** Function to wait for SHT75 reading *****
 
void comwait (void)
{
 int16 sht_delay;
 
 output_float(sht_data_pin);                     //data high
 output_bit(sht_clk_pin, 0);                     //clk low
 delay_us(1);
 for(sht_delay=0; sht_delay<30000; sht_delay++)  // wait for max 300ms
  {
   if (!input(sht_data_pin)) break;              //if sht_data_pin low, SHT75 ready
   delay_us(10);
  }
}
 
//***** Function to reset SHT75 communication *****
 
void comreset (void)
{
 int8 i;
 
 output_float(sht_data_pin);    //data high
 output_bit(sht_clk_pin, 0);    //clk low
 delay_us(2);
 for(i=0; i<9; i++)
  {
   output_bit(sht_clk_pin, 1);  //toggle clk 9 times
   delay_us(2);
   output_bit(sht_clk_pin, 0);
   delay_us(2);
 }
 comstart();
}
 
//***** Function to soft reset SHT75 *****
 
void sht_soft_reset (void)
{
 comreset();           //SHT75 communication reset
 comwrite(0x1e);       //send SHT75 reset command
 delay_ms(15);         //pause 15 ms
}
 
//***** Function to measure SHT75 temperature *****
 
int16 measuretemp (void)
{
 int1 ack;
 int16 iobyte;
 
 comstart();             //alert SHT75
 ack = comwrite(0x03);   //send measure temp command and read ack status
 if(ack == 1) return;
 comwait();              //wait for SHT75 measurement to complete
 iobyte = comread();     //read SHT75 temp data
 return(iobyte);
}
 
//***** Function to measure SHT75 RH *****
 
int16 measurehumid (void)
{
 int1 ack;
 int16 iobyte;
 
 comstart();            //alert SHT75
 ack = comwrite(0x05);  //send measure RH command and read ack status
 if(ack == 1) return;
 comwait();             //wait for SHT75 measurement to complete
 iobyte = comread();    //read SHT75 temp data
 return(iobyte);
}
 
//***** Function to calculate SHT75 temp & RH *****
 
void calculate_data (int16 temp, int16 humid, float & tc, float & rhlin, float & rhtrue)
{
 float truehumid1, rh;
 
 //calculate temperature reading
 tc = ((float) temp * 0.01) - 40.0;
 
 //calculate Real RH reading
 rh = (float) humid;
 
 rhlin = (rh * 0.0405) - (rh * rh * 0.0000028) - 4.0;
 
 //calculate True RH reading
 rhtrue = ((tc - 25.0) * (0.01 + (0.00008 * rh))) + rhlin;
}
 
//***** Function to measure & calculate SHT75 temp & RH *****
 
void sht_rd (float & temp, float & truehumid)
{
 int16 restemp, reshumid;
 float realhumid;
 restemp = 0; truehumid = 0;
 
 restemp = measuretemp();    //measure temp
 reshumid = measurehumid();  //measure RH
calculate_data (restemp, reshumid, temp, realhumid, truehumid);  //calculate temp & RH
}
 
//***** Function to initialise SHT75 on power-up *****
 
void sht_init (void)
{
 comreset();    //reset SHT75
 delay_ms(20);  //delay for power-up
}
void main()
{
 float restemp, truehumid;
 lcd_init();
sht_init();
 
 while(1)
 {
  sht_rd (restemp, truehumid);
  printf(lcd_putc,"Temp : %3.1f %cC   ", restemp, 223);
  printf(lcd_putc,"\nRH   : %3.1f %%   ", truehumid);
  delay_ms(500);        //delay 500 ms between reading to prevent self heating of sensor
 }
}